Bravetti Mixer EP585H User Manual

EP585H  
ONE (1) YEAR LIMITED WARRANTY  
EURO-PRO OPERATING LLC warrants this product to be free from defects in material  
and workmanship for a period of one (1) year from the date of purchase when utilized for  
normal household use.  
If your appliance fails to operate properly while in use under normal household  
conditions within the warranty period, return the complete appliance and accessories,  
freight prepaid to EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh,  
N.Y. 12901. If the appliance is found to be defective in material or workmanship, EURO-  
PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and  
$12.95 to cover the cost of return shipping and handling must be included.*  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or  
replacement of the unit at our option. This warranty does not cover normal wear of parts  
and does not apply to any unit that has been tampered with or used for commercial  
purposes. This limited warranty does not cover damage caused by misuse, abuse,  
negligent handling or damage due to faulty packaging or mishandling in transit.  
This warranty is extended to the original purchaser of the unit and excludes all other  
legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if  
any, is limited to the specific obligations expressly assumed by it under the terms of the  
limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or  
CONVERTIBLE  
HAND/STAND MIXER  
OWNER’S MANUAL  
Model EP585H  
127V., 60Hz., 325 Watts  
consequential damages of any nature whatsoever. Some states do not permit the  
exclusion or limitation of incidental or consequential damages, so the above may not  
apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which  
vary from state to state.  
*Important: Carefully pack item to avoid damage in shipping. Be sure to include  
proof of purchase date and to attach tag to item before packing with your name,  
complete address and phone number with a note giving purchase information,  
model number and what you believe is the problem with item. We recommend you  
insure the package (as damage in shipping is not covered by your warranty). Mark  
the outside of your package “ATTENTION CUSTOMER SERVICE”. We are  
constantly striving to improve our products, therefore the specifications contained  
herein are subject to change without notice.  
---------------------------------------------------------------------------------------------------------------------------  
OWNERSHIP REGISTRATION CARD  
Please fill out and mail the product registration card within ten (10) days of purchase.  
The registration will enable us to contact you in the unlikely event of a product safety  
notification. By returning this card you acknowledge to have read and understood the  
instructions for use, and warnings set forth in the accompanying instructions.  
RETURN TO EURO-PRO OPERATING LLC, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901  
EP585H  
______________________________________________________________________  
Appliance model  
______________________________________________________________________  
Date purchased  
Name of store  
______________________________________________________________________  
Owner’s name  
For information or assistance:  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
_
_____________________________________________________________________  
Address  
City  
State  
Zip Code  
7
Tel.: 1 (800) 798-7398  
Printed in China  
 
GETTING TO KNOW YOUR CONVERTIBLE  
HAND/STAND MIXER  
OPERATING INSTRUCTIONS  
Fitting the Bowl onto the  
Using the Convertible Hand/Stand  
Mixer  
Turntable of the Stand  
Warning: To avoid injury when  
assembling the hand mixer to the  
stand, always set the speed selector on  
0and unplug the appliance.  
Warning: To avoid injury when  
assembling the hand mixer to the  
stand, always set the speed selector on  
0and unplug the appliance.  
1. Place the base of the mixing bowl  
onto the turntable of the stand. To  
fully lock the mixing bowl in place,  
press down and turn the mixing bowl  
in a clockwise direction until you hear  
it click into place. (Fig. 9)  
1. Before plugging the hand/stand mixer  
into the electrical outlet, assemble the  
unit with the desired accessories.  
2. Set the speed selector switch to the  
HIor LOposition.  
3. Select the speed that you desire.  
MIXING GUIDE  
MIXING  
TASK  
RECOMMENDED  
SPEED(S)  
Folding &  
Blending  
“LO” 1 & 2  
“LO” 3 & 4  
Fig. 9  
Light Mixing  
Creaming &  
Beating  
“HI” 6 - 8 or “LO” 5  
2. To remove the mixing bowl from the  
stand, press down and turn the mixing  
bowl counter clockwise. The mixing  
bowl can now be detached from the  
turntable and lifted away. (Fig. 10)  
Whipping &  
Aerating  
“HI” 9 & 10 or  
BURST  
12  
14  
13  
4. Select the bowl speed – “LOor HI”  
depending on how fast you want the  
bowl to turn. Use the LObowl  
speed for mixing speed 1-5. Use the  
HIbowl speed for mixing speed  
6-10. If you do not wish the bowl to  
turn, leave the bowl speed in the  
OFFposition.  
15  
Note:  
Fig. 10  
Always select the speed setting  
before the mixing bowl speed to  
prevent ingredients from being flicked  
out of the mixing bowl.  
Always start mixing at slow speeds  
and increase the speed gradually to  
prevent the ingredients splashing out  
of the bowl.  
1. Hi-Lo Speed Selector  
2. Speed Control  
3. Burst of Speed Button  
4. Beater Eject Button  
5. Beaters  
6. Stainless Steel Bowl  
7. Tilt Button  
8. Hand Mixer Release Button  
9. Bowl Speed Control Dial  
10. Hand Mixer  
11. Base Stand  
12. Dough Hooks  
13. Plastic Bowl  
14. Bowl Lid  
Note: It is easier to fit the mixing bowl to  
the turntable when the hand mixer is not  
attached to the pivot support.  
15. Spatula  
Technical Specifications  
Voltage:  
Power:  
Bowl Capacity:  
127V., 60Hz.  
325Watts  
3.5 Qts.  
2
5
 
Read all the sections of this booklet and follow all the instructions carefully.  
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
Assembling the Hand Mixer to  
the Stand  
Warning: To avoid injury when  
assembling the hand mixer to the  
stand, always set the speed selector on  
0and unplug the appliance.  
3. While the hand mixer is still in the  
raised position, insert either the  
beaters or the dough hooks.  
4. To lower the hand mixer, press and  
hold the tilt button with one hand  
while holding the hand mixer with the  
other hand and slowly lower the hand  
mixer down. (Fig. 6)  
Attaching the Dough Hooks to  
the Hand Mixer  
Warning: To avoid injury when  
inserting or removing beaters or  
1. Ensure that the hand mixer is not  
plugged in to an electrical outlet  
and that the speed control switch  
is on the 0(off) position.  
2. The dough hooks have a set  
method of fitting into the hand  
mixer because they are not  
dough hooks, always set the speed  
selector on 0and unplug the appliance.  
1. Before using your Bravetti  
Convertible Hand/Stand Mixer for  
the first time, wash the beaters,  
dough hooks, bowls and spatula in  
warm, sudsy water. Rinse and dry  
thoroughly. Use a damp cloth to wash  
over the mixer base and the hand  
mixer. Dry with a soft cloth.  
1. Press the tilt button, located on the  
top of the support pivot . While the  
button is depressed, ease the support  
pivot back. (Fig. 4)  
Press the  
tilt button  
and tilt the  
hand  
mixer  
down  
identical. One has a grommet and  
the other does not. (Fig. 2)  
Tilt Button  
NEVER immerse the base stand or  
the hand mixer in water or any other  
liquids.  
Support  
Pivot  
Grommet  
2. Before assembling your Convertible  
Hand/Stand Mixer, make sure that the  
power cord is unplugged from the  
electrical outlet and that both the  
speed control and the base speed  
control dial are in the OFFposition.  
Fig. 6  
Fig. 2  
Fig. 4  
The support pivot will lock into this  
raised position until it is released by  
pressing the tilt button again.  
5. To remove the hand mixer from the  
pivot support, first raise the mixer by  
pressing the tilt button and raise the  
mixer up. (Fig. 7) the mixer will lock  
into the raised position.  
6. Then press the mixer release button  
which is located on the under side of  
the pivot support with one hand and  
with the other lift the hand mixer by  
the handle upwards and away from  
the support pivot. (Fig. 8)  
3. Looking at the under side of the  
hand mixer, you will see that one  
of the sockets has a red dot over  
it. (Fig. 3) Insert the dough hook  
with the grommet into this socket.  
Attaching the Beaters to the  
Hand Mixer  
1. Ensure that the hand mixer is not  
plugged in to an electrical outlet  
and that the speed control switch  
is on the 0(off) position.  
2. To connect the hand mixer to the  
support pivot, locate the two retaining  
prongs on the support pivot into the  
two rectangular holes in the heel of  
the hand mixer. (Fig. 5) When the  
hand mixer is seated on the support  
pivot, press down on the hand mixer  
to click it into place and lock the hand  
mixer and the support pivot together.  
2. Insert the beaters into the sockets  
on the under side of the hand  
mixer and twist counter clockwise  
until the beater is firmly fitted into  
the socket.  
3. To release the beaters from the  
unit, press on the beater eject  
button on the front of the unit and  
they will pop out. (Fig. 1)  
Grommet  
Press the  
tilt button  
and tilt the  
hand  
mixer up  
Rectangular  
holes  
Fig. 3  
Press  
eject  
4. Then insert the other dough hook  
into the other socket. Push both  
dough hooks in until you hear a  
click confirming that they are  
securely in place.  
5. To release the dough hooks from  
the unit, press on the beater eject  
button on the front of the unit and  
they will pop out. (Fig. 1)  
Note: Ensure that the beaters or  
dough hooks are fully inserted into  
the correct sockets or your mixing  
results may be affected.  
Fig. 7  
button  
Retaining  
prongs  
Support  
pivot  
Fig. 5  
Note: Ensure that the two retaining  
prongs on the support pivot are fully  
connected into the hand mixer.  
Hand  
mixer  
release  
button  
Fig. 1  
Fig. 8  
3
4
 

Belkin Server 5000HQ User Manual
Blomberg Refrigerator KGM 9690 User Manual
Bolens Snow Blower 191 967 A User Manual
Canon Printer 6221B030 User Manual
Canon Scanner 300 User Manual
Casio Cash Register SE S10 User Manual
Casio Clock DQD 70B User Manual
Casio Digital Camera EX P700 User Manual
Changhong Electric Flat Panel Television W270F8E, W320F8E, W370F8E User Manual
Chief Manufacturing Indoor Furnishings PAC501 User Manual